diff --git a/spinnyboy_rust/src/bin/main.rs b/spinnyboy_rust/src/bin/main.rs
index b621a30..97ab0f0 100644
--- a/spinnyboy_rust/src/bin/main.rs
+++ b/spinnyboy_rust/src/bin/main.rs
@@ -5,15 +5,17 @@
     reason = "mem::forget is generally not safe to do with esp_hal types, especially those \
     holding buffers for the duration of a data transfer."
 )]
+use core::fmt::Write;
+use esp_hal::uart::{Config, Uart};
 
 use esp_hal::clock::CpuClock;
+use esp_hal::delay::Delay;
+use esp_hal::main;
 use esp_hal::mcpwm::operator::PwmPinConfig;
 use esp_hal::mcpwm::timer::PwmWorkingMode;
 use esp_hal::time::Rate;
-use esp_hal::timer::timg::TimerGroup;
-use esp_hal::main;
 use esp_hal::time::{Duration, Instant};
-use esp_hal::delay::Delay;
+use esp_hal::timer::timg::TimerGroup;
 use rtt_target::rprintln;
 mod dc_driver;
 use dc_driver::afroesc::AfroEsc;
@@ -40,36 +42,49 @@ fn main() -> ! {
     let mut delay = Delay::new();
 
     esp_alloc::heap_allocator!(#[esp_hal::ram(reclaimed)] size: 65536);
-    let clock_config = esp_hal::mcpwm::PeripheralClockConfig::with_frequency(Rate::from_mhz(32)).unwrap();
+    let clock_config =
+        esp_hal::mcpwm::PeripheralClockConfig::with_frequency(Rate::from_mhz(32)).unwrap();
     let mut mcpwm = esp_hal::mcpwm::McPwm::new(peripherals.MCPWM0, clock_config);
     mcpwm.operator0.set_timer(&mcpwm.timer0);
     let pin = peripherals.GPIO18;
 
-    let mut pwm_pin = mcpwm.operator0.with_pin_a(pin, PwmPinConfig::UP_ACTIVE_HIGH);
-        let timer_clock_cfg = clock_config
+    let mut pwm_pin = mcpwm
+        .operator0
+        .with_pin_a(pin, PwmPinConfig::UP_ACTIVE_HIGH);
+    let timer_clock_cfg = clock_config
         .timer_clock_with_frequency(19_999, PwmWorkingMode::Increase, Rate::from_hz(50))
         .unwrap();
     mcpwm.timer0.start(timer_clock_cfg);
     let mut esc = AfroEsc::new(&mut pwm_pin);
     esc.set_timestamp(1000);
-    delay.delay_millis(3000); 
-    esc.set_duty_percent(10);    
-    delay.delay_millis(3000);    
+    delay.delay_millis(3000);
+    esc.set_duty_percent(10);
+    delay.delay_millis(3000);
     //1421 is I think the best, makes calculating the throttle easier
     esc.set_timestamp(1055);
-    delay.delay_millis(3000);    
+    delay.delay_millis(3000);
 
+    let mut uart0 = Uart::new(peripherals.UART0, Config::default().with_baudrate(9600))
+        .unwrap()
+        .with_rx(peripherals.GPIO9)
+        .with_tx(peripherals.GPIO10);
+    uart0.write(b"page page1");
+    uart0.write(b"\xff");
+    uart0.write(b"\xff");
+    uart0.write(b"\xff");
+    uart0.write(b"\xff");
+    rprintln!("WRITE HAPPENED!");
     // Example: Ramp from 0% to 50% throttle
-        //the afro esc starts turning at roughly setup gets a PWM at 
+    //the afro esc starts turning at roughly setup gets a PWM at
     //loop{
     //     for pulse in 1120..1500 {
     //         rprintln!("pulse:{}",pulse);
     //         pwm_pin.set_timestamp(pulse);
     //         Timer::after_millis(3000).await;
     //     }
-        
+
     //     Timer::after_millis(1000).await;
-        
+
     //     // Return to idle
     //     pwm_pin.set_timestamp(1000);
     //     Timer::after_millis(1000).await;
@@ -77,8 +92,7 @@ fn main() -> ! {
 
     loop {
         rprintln!("Hello world!");
-    delay.delay_millis(3000);    
-
+        delay.delay_millis(3000);
     }
 
     // for inspiration have a look at the examples at https://github.com/esp-rs/esp-hal/tree/esp-hal-v1.0.0/examples/src/bin